View Full Version : Problems with sight in!
04-13-2012, 08:19 AM
Hey guys, anybody ever have trouble sighting i a 2011 pantera? Mine is shooting low and my sight is out of adjustment. Im using a Cobra Stealth Plus 5 pin sight and a whisker biscuit rest. Im new to bow shooting and any suggestions would be nice. Thanks in advance!
04-13-2012, 08:28 AM
Use this video, worked great for me.
04-13-2012, 10:16 AM
Move your peep up a bit.
04-13-2012, 10:32 AM
With today's bows and sights this should not be a problem, but it does crop up once in a while. In almost all cases it is because the shooter (you) are anchoring too high. You didn't give much detail, but in most cases, if you are using peep sight then it should be about 5 1/2" to 6" above the nocking point. Moving it up to this point will force you to anchor lower. In this case if you are using anchor referrences such as touching the tip of your nose to the string you may have to change the draw length to do so.
I suggest you post more specific info such as the bow's draw length, draw weight, the arows you are shooting. Also have you been measured for what drawlength would fit you best? How high is your peep now and kisser button if you are using one? Better yet would be a picture from the side of you at full draw, head to foot so we can see how the bow fits you.
I could write a book explaining more, but being you're new I don't want to clutter your mind at this point.
04-13-2012, 10:47 AM
When at full draw my arrow is between my lower lip an my chin wen looking through the peep. Is that to low or can i move peep up? My draw length is 27" DW 65lb. My arrows are gold tip from cabelas.
04-13-2012, 10:54 AM
Lot's of variables here..rest type and adjustment, setup etc. peep location, like others have said...anchor etc. I'm confident there are plenty of folks here to get you lined out..a pic at full draw will help them help you. :) The whisker biscuit may be out of adjustment..put a bow square on it and check it out..there is no substitute for a proper setup before you try sighting in.
Typically you establish an anchor first (usually around the corner of the mouth for most) then draw, anchor, and have some adjust the peep while the bow is drawn. After your setup is squared (rest and centershot, nock point or d-loop all adjusted properly) you simply follow the arrow with the pin to get it sighted in. Hope I haven't confused you.
04-13-2012, 11:47 AM
Here is another source for good information:
Click me! (http://martinarchery.com/mtechforum/forumdisplay.php?20-Bow-Setup-Tips)
04-13-2012, 02:44 PM
As already been said move the peep. The most common problem I find with bows in the shop the peep is always to low. Most of the ones I set are 5 1/2 to 6" up from dead center of the d loop. Once drawn level and the peep adjusted. It usually not far off from these measurements.
04-13-2012, 04:45 PM
Ya, i have thought about raising the peep but there is a point were u can get it to high isnt there? It feels high to me already but again im still new to it all.
04-13-2012, 06:10 PM
Ya, i have thought about raising the peep but there is a point were u can get it to high isnt there? It feels high to me already but again im still new to it all.Draw your bow back with your eyes closed and the bow level. Open your eyes and check to see if your peep is in the proper location. If not have some one slide it to the right location.
04-13-2012, 06:28 PM
Maybe you can move your rest up or move your d loop up
04-13-2012, 07:38 PM
Thanks for all the help guys. I just moved my peep up a littel bit an that took care of the problem.
Powered by vBulletin® Version 4.1.12 Copyright © 2013 vBulletin Solutions, Inc. All rights reserved.