Search:

Type: Posts; User: themiddleman

Page 1 of 2 1 2

Search: Search took 0.12 seconds.

  1. Replies
    17
    Views
    425

    topnock give me a call. I'm the largest Martin...

    topnock give me a call. I'm the largest Martin dealer in the state of Idaho and would be glad to help you out.

    Pat Finney
    Prairie Archery
    208-507-1102
  2. Replies
    8
    Views
    157

    Is it possible to convert a 2010 two 2013 Martin...

    Is it possible to convert a 2010 two 2013 Martin Bows over to the new split limbs yes. The problem is the solid limbs are 2 1/2 inches longer than the new split limbs. You would end up with a bow...
  3. Replies
    6
    Views
    616

    the Nitro 3 cams are actually stronger than the...

    the Nitro 3 cams are actually stronger than the Nitro 2 cams. They are made out of a much tougher 7000 series aluminum
  4. Powerlineman83 what you are trying to do is...

    Powerlineman83 what you are trying to do is pretty involved. Give me a call I am sure I can help you out.

    Pat Finney
    Prairie archery
    208-507-1102
  5. Powerlineman83 Sent you a pm.I think i can help...

    Powerlineman83 Sent you a pm.I think i can help you out.
  6. Replies
    3
    Views
    285

    The Phantom and the blade X4 are only offered in...

    The Phantom and the blade X4 are only offered in right hand.
  7. warthog limbs

    I'm pretty sure what you have is a 2009 warthog not a 2010. The Roto cup was changed between the 2009 and 2010 warthog and the limbs were narrowed. if you can post a picture we can tell you for sure....
  8. Replies
    20
    Views
    1,612

    Barnsdale Limbs

    I have two rytera alien x the axle to axle is 32 inches with a 7 inch brace height. The 70 pound alien X limb deflection number is 115 my 60 pound alien x limb deflection number is 135.
    Hope this...
  9. Sight has sold

    Sight has sold
  10. Replies
    7
    Views
    1,412

    The reason you are having trouble adjusting the...

    The reason you are having trouble adjusting the draw module on the Pantera is because the Panteras cam is cloaked.The film dip add several thousands to an already tight fitting part. On the left side...
  11. Sight sold pending payment

    Sight sold pending payment
  12. Replies
    7
    Views
    519

    On the left side of the XT cam next to the to...

    On the left side of the XT cam next to the to draw module screws you will see the end of the pivot post for the draw module just give it a little tap. . Don't forget to adjust the draw stop after you...
  13. I wasn't getting any interest in the sight and...

    I wasn't getting any interest in the sight and scope combination. I had an offer for the scope by itself and I sold it. I am now selling the Shibuya sight without a scope for $165 TYD
  14. Shibuya carbon cp 365 sight with 1 3/8 CR Apex scope

    I have a Shibuya carbon cp 365 sight for-sale. [THE APEX SCOPE HAS SOLD]
    The sight had a 9 inch bar and was too long for my set up. I cut 2 inches off the back and is now a 7 inch bar. This was my...
  15. Replies
    9
    Views
    915

    scepter v

    I had two of the original 39 inch ATA prototype shadowcats and they were outstanding bows. As far as I'm concerned Martin made a big mistake when they decided to added 2 1/4 inches to the sight...
  16. Replies
    7
    Views
    707

    Fury XT cam

    When you put the cable on the -10 peg you are essentially lengthening the bus cable.By doing so it will make the draw length shorter and reduce your maximum poundage by approximately 10 pounds and...
  17. Replies
    3
    Views
    356

    prowler XT

    Capital ken I hate to be the bearer of bad news but you should have bought a 70 pound bow and set it on the -10 peg that would have allowed you to go to your 26 draw length at 60 pounds. You can...
  18. Replies
    25
    Views
    1,659

    tuning a firecat

    If you could post a few pictures of your bow. one with the bow at rest with an arrow on it and one with the bow it full draw with an arrow on it. Also, maybe a couple pictures of the top and bottom...
  19. Replies
    25
    Views
    1,659

    Firecat 400

    binary hybrid cams are simple to tune. Adjust the timing, adjust draw module, adjust the draw peg. If all that was done correctly and your arrows are spine correctly for that set up and you're not...
  20. Martin cheetah

    My name is Pat and I am the owner of Prairie archery. give me a call and I will help you out.

    Prairie archery.
    208-507-1102
  21. Replies
    42
    Views
    3,240

    davik if you want to switch from the Nitro 3s...

    davik if you want to switch from the Nitro 3s [short draw cams] to the Nitro 3L [long draw cams] and you want to keep the bows Max pounds then yes you will have to change the cams, limbs, and the...
  22. Replies
    42
    Views
    3,240

    That is not what I'm saying at all the 2013 Nitro...

    That is not what I'm saying at all the 2013 Nitro 3 and the 2012 Nitro 2 are virtually the same cams. The Nitro 3 is just a lighter updated version of the Nitro 2. What I am saying is the larger 2.0...
  23. scepter v

    peace as long as butch is a Martin Pro series dealer he can ordered it with a 1 min phone call to Carly at Martin archery. You should have it in two weeks max.
  24. Replies
    42
    Views
    3,240

    Nitro 3 cams

    [QUOTE=joelc;101734]Now I dont know...a dealer called today that read this thread and said he noticed approx. 10 fps difference between the cams favoring the larger 2.0 cam. In all of my years here...
  25. Replies
    43
    Views
    5,626

    Diabalo

    I played with the prototype a few months back and was very impressed. I have a couple on order for the shop. I talked to Martin archery the other day and they said they should start shipping by the...
Results 1 to 25 of 38
Page 1 of 2 1 2