Results 1 to 10 of 11

Thread: Questions about Scepter II ?

Hybrid View

  1. #1
    Woody
    Guest

    Default Questions about Scepter II ?

    Hello, I have recently purchased a secondhand Scepter II Pro Series with Elite Limbs, I've only had it for about 3-4 months now, but i like it a lot, It's certainly a big step up from the Black Bear II that i used to have ! I regularly top score at my club now, which is quite satisfying, I must say ! What size do the Elite Limbs go up to ? the stamp on mine says either, 9H or H6, I'm not sure which Cams it has, but with the bow adjusted all the way up it said about 73 pound on the scale, but i'm not sure how acurate the scale was, i'm guessing it should have said 70 or 75 pound not 73 pound, as i shoot FITA with it, I only need 60 pound but that has the Limb ends almost out of their pockets ! also when i set the tiller to zero, i notice that the cams are not perfectly synchronized, I have been told that cam sync is more important than zero tiller, so does that mean i should try to get the cams sync'ed, regardless of what it does to the tiller, or is there a middle ground i should be aiming for ? I can't get my arrows to fly straight out of the bow, sometimes i can see the arrow in flight as it leaves the bow and the tail of the arrow is corkscrewing through the air ? my rest is set approximately 3/4 of an inch from the side of the bow, my arrows are gold tip ultralight pro's ! everything seems to be set correctly, except for the cams not being perfectly sync'ed !

    any and all help is greatly appreciated, as well as any info on the scepter II pro series ?

    Thanks

    Woody

  2. #2
    Woody
    Guest

    Default

    Hello, It's me again, I thought i should mention that i live in a rural area in Australia, so taking the bow to a martin dealer is out of the question ! also how can i figure out which type of cams it has, I looked on the cam charts but that just made it more confusing, I'll post some pics up, and i'd like any and all information about the bow, year of manufacture ? is it standard, or has it been modified, plus any tips on how to set it up correctly for the most accurate shooting ?







    all advice and Information welcome

    Thanks

    Woody

  3. #3
    Woody
    Guest

    Default

    Yes, It's me again, I've looked through the online manuals, and there aren't any Scepter II manuals, or any Scepter manuals at all, I bought this bow secondhand and it not have any manual with it when i bought it ! If anyone has a Scepter II Pro Series manual, could they send me a copy please ? From what i have read from the other manuals, they all say that Cam sync should be done at full draw, is this the same with the scepter II ? Also can someone explain to me what the difference is between, M-57 Scepter II and M-57 XRG Scepter II ?

    Thanks Again

    Hope to hear from someone soon ?

    Woody

  4. #4
    Woody
    Guest

    Default

    O.K, What's the bloody deal ???? I've posted on here several times with no responses, and I've tried the "contact us" section as well only to have all my e-mails returned saying that address no longer accepts e-mails ??? What kind of crappy setup is this , firstly Martin Tech's don't even read the "so called Martin Tech forum", and then when you try to contact them through the "contact us" section you get told that address is no longer valid, WTF ??? I have to say this situation leaves me far from impressed, I would have thought that a company as well known as martin, would have it's act together a bit more than this ? This whole site appears to be some kind of joke, with no-one from martin even on here, or giving a damn !

    Woody

  5. #5
    Myk
    Guest

    Default

    Aren't you the impatient one.
    If you're that impatient you should register at Archerytalk.com. You seem to not know much about archery in general so Archerytalk would be a good place for you to learn. There are also a lot of Martin shooters there.
    There's lot more traffic there so you'll get answered faster.
    You need to realize that you're asking about a pretty old bow on a forum that doesn't get a lot of traffic and you asked a million questions.

    My guess is that's a 1998 bow.

    I don't know if it's the highest but there are 11H Elite limbs.

    I think those are Z-Cams but I'm not sure.

    73lbs could be right. Draw weights are not exact and as you say, neither are many scales.

    Martin has a 15lb range. You are OK to shoot the bow 5 turns out with each limb bolt.
    The pocket is not what holds the limbs, there are two mushrooms in the limbs that fit into holes in the pockets that hold the limbs. Don't worry about the end of the limbs being out of the pocket. Just don't shoot with the bolts more than 5 turns out.

    To set your tiller to zero you crank the limb bolts in all the way. That is factory set tiller. Then you back the bolts out equally to keep that setting.

    Setting the cam timing should not effect your tiller.

    I kind of doubt corkscrewing arrows is your cam timing, so no, everything is not set correctly. Cam timing is an up and down thing. Corkscrewing indicates a combination side to side and an up and down problem. It can be a contact problem, a rest problem or a torque problem.

    Martin doesn't have bow specific manuals.
    Yes cam timing is checked at full draw, but I wouldn't try to adjust it at full draw. That sounds like a recipe for disaster to both bow and body.

    You say the email address no longer accepts emails, that could mean their box is full. If the address was no longer valid you get something totally different called a maildaemon.
    But most companies are terrible about answering emails anyway.

    XRG is the Elite limbs.

    This little doo-hickey is how you adjust your cam timing. The cam's a little different than my friend's old steel cabled Z-Cam (which is why I'm not sure that's the cam it is) but that adjuster is the same as his.

    Looks like a pretty nice set up.
    Attached Images Attached Images

  6. #6
    Woody
    Guest

    Default

    Thank You, I've figured out most of it myself already, I've fiddled with nock height, rest height, left/right alignment of the rest, and I eventually realised about the cam adjusters, It seems to be shooting better now ? I just figured since i have a martin bow, the martin website would be the best place to visit, You know, get the word from the horse's mouth ! Sorry if it seems that i'm impatient, everything was fine untill i tried to use the "contact us" section, then i started getting frustrated ! Thanks again for your response

    Woody

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •