Page 2 of 2 FirstFirst 12
Results 11 to 20 of 20

Thread: Finally pics

  1. #11
    String builder/ Super Moderator Hutch~n~Son Archery's Avatar
    Join Date
    Aug 2009
    Location
    Gilmanton, New Hampshire
    Posts
    5,777
    Post Thanks / Like

    Default

    BRH, I just looked at mine. Your lean is not that much more than mine. Does your cable slide have the string on the outside groove and in the shortest part of the glide? With the cable in the longest grove. Also I took a lot of lean out by measuring the ata on both sides and matched them by twisting the yoke till they were the same.


    Hutch
    Last edited by Hutch~n~Son Archery; 09-23-2011 at 06:24 PM.
    Bow String Depot Custom String Builders
    Need a string set pm or email me @ bowstringdepot@gmail.com
    or check us out @ http://bowstringdepot.com

  2. #12
    String builder/ Super Moderator Hutch~n~Son Archery's Avatar
    Join Date
    Aug 2009
    Location
    Gilmanton, New Hampshire
    Posts
    5,777
    Post Thanks / Like

    Default

    By the looks of that pic the cable slide is equal causing the cable to have excessive pull. My cable slide is grey and has a very long section for the cable.



    Hutch
    Bow String Depot Custom String Builders
    Need a string set pm or email me @ bowstringdepot@gmail.com
    or check us out @ http://bowstringdepot.com

  3. #13
    Senior Member
    Join Date
    Feb 2011
    Location
    colorado
    Posts
    254
    Post Thanks / Like

    Default

    ok update:

    Measured from edge of idler wheel to black string 1/2", measured from edge of idler wheel to red string 3/8 inch. i do have idler wheel lean!
    2010 Rytera Nemesis. 63lbs/29dl 292 fps 384gr arrow. Sword 6 pin sight

  4. #14
    Senior Member
    Join Date
    Oct 2009
    Location
    michigan
    Posts
    510
    Post Thanks / Like

    Default

    from the looks of that pix, it seems the cable guide is pulling it way out . just a guess

  5. #15
    String builder/ Super Moderator Hutch~n~Son Archery's Avatar
    Join Date
    Aug 2009
    Location
    Gilmanton, New Hampshire
    Posts
    5,777
    Post Thanks / Like

    Default

    Sonny is right on the yoke. Most of the Martins are 7 inch yokes. But the Bengal is 8 inches. So from the end of the loop to the serving it should be 8 inches. If it is not that can change how it pulls the idler over.

    Hutch
    Bow String Depot Custom String Builders
    Need a string set pm or email me @ bowstringdepot@gmail.com
    or check us out @ http://bowstringdepot.com

  6. #16
    Senior Member
    Join Date
    Feb 2011
    Location
    colorado
    Posts
    254
    Post Thanks / Like

    Default

    from what hutch said its 7 inches from serving to end of loop.
    2010 Rytera Nemesis. 63lbs/29dl 292 fps 384gr arrow. Sword 6 pin sight

  7. #17
    String builder/ Super Moderator Hutch~n~Son Archery's Avatar
    Join Date
    Aug 2009
    Location
    Gilmanton, New Hampshire
    Posts
    5,777
    Post Thanks / Like

    Default

    That would be confirming what Sonny said. That yoke is too short and is causing some of the problem.


    Hutch
    Bow String Depot Custom String Builders
    Need a string set pm or email me @ bowstringdepot@gmail.com
    or check us out @ http://bowstringdepot.com

  8. #18
    Senior Member
    Join Date
    Feb 2011
    Location
    colorado
    Posts
    254
    Post Thanks / Like

    Default

    ok thanks for the info pretty soon hutch u will have an order for me since u know martins standards. Just waiting on the money.
    2010 Rytera Nemesis. 63lbs/29dl 292 fps 384gr arrow. Sword 6 pin sight

  9. #19
    String builder/ Super Moderator Hutch~n~Son Archery's Avatar
    Join Date
    Aug 2009
    Location
    Gilmanton, New Hampshire
    Posts
    5,777
    Post Thanks / Like

    Default

    Not a problem, I would like to see that Bengal shoot as smooth as mine. Once you get a set of strings on it, there will be a few adjustments to get the correct specs and you should be right on the money.

    Hutch
    Bow String Depot Custom String Builders
    Need a string set pm or email me @ bowstringdepot@gmail.com
    or check us out @ http://bowstringdepot.com

  10. #20
    Senior Member
    Join Date
    Feb 2011
    Location
    colorado
    Posts
    254
    Post Thanks / Like

    Default

    Ok so had someone look at pics and low and behold............... the cable slide was on backwards. Loosened limbs, flipped the cable slide and whaaaaalaaaaaaaaaa i have full clearence on my string. Well since the only one who messed with it was the guy who put the last set of strings on my bow, i think he needs a kick to the shins. Thank you all who threw ur imput in trying to help me solve my issue. Hutch, sent u and email any ?s give me a
    call.
    2010 Rytera Nemesis. 63lbs/29dl 292 fps 384gr arrow. Sword 6 pin sight

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •