Page 1 of 4 123 ... LastLast
Results 1 to 10 of 35

Thread: Aerovanes

  1. #1
    flytier17
    Guest

    Default Aerovanes

    Anybody used these? What do you think.

    They use lift, like 3 mini aeroplane wings to spin the shaft, not drag. They have silent flight as well. And, they are fletched straight, and have no kicker like a quickspin. Aparrently they will spin the arrow more intensly than a quickspin with no drag. They are also stiff, so as not to distort at high speeds. Arrow trajectory is flatter too. @ 40yds, my FMJ's jumped an unbelievable 17" up, while @ 10 yds they were only 1.5" high. My pins are half as far apart, and the arrow weight is the same. Sounds like a plus for 3-D. Also, my 60yd groups went from 8" to 4.5". I like them a lot.

  2. #2
    vision archery
    Guest

    Default

    No I haven't but sounds like something I need to look into. Thanks for the info.

    Joe

  3. #3
    Senior Member
    Join Date
    Nov 2007
    Location
    Germany
    Posts
    2,008
    Post Thanks / Like

    Default

    Hey Alec. Give us some details, pictures, prices.
    (2) Hoyt PCEXL

  4. #4
    Banned
    Join Date
    Dec 2008
    Location
    Henry, IL
    Posts
    22
    Post Thanks / Like

  5. #5
    flytier17
    Guest

    Default

    Hello Dorge, nice to see you over here as well. Welcome to the Martin Forum!

    Like you can see in my post, I did get some Gen. 1 vanes from the AT classifieds. So far I am extremely impressed. I am holding out till the Gen. II comes out to buy more. I intend to have them adorning my 3-D arrows, as well as my hunting arrows if they can steer a Silver Flame correctly.

  6. #6
    Senior Member
    Join Date
    Nov 2007
    Location
    Germany
    Posts
    2,008
    Post Thanks / Like

    Default

    Hey Alec. You are shooting Silver Flames? Great choice.
    (2) Hoyt PCEXL

  7. #7
    Super Moderator bfisher's Avatar
    Join Date
    Nov 2005
    Location
    Middletown, Pa, USA
    Posts
    11,584
    Post Thanks / Like

    Default

    OK Dorge,

    I don't shoot vanes that often, usually because of the increased weight compared with feathers. However, I always like some new technology and don't dismiss it without having tried it for myself. I don't often ely on the inexperience of other to do my judging. So where can I buy a few of these things to try? I need the version that would be used mainly in 3D. Not interested in anything for broadheads at this time.

    How might they work off a Trophy Taker Spring Steel?

    For the record I've never shot Blazers. Not crazy about high profile.

    Barry
    If You're Not Living on the Edge You're Taking Up Too Much Space
    Martin Gold Plus Staff Shooter
    Alien Mafia
    PSAA Life member, UBP Life member
    PADI AOW Diver

  8. #8
    flytier17
    Guest

    Default

    Simon; I shoot Slick Tricks now. However, My FMJ's have only 7 that still fly right due to groups and RH's, and to get them to spine right, I had to cut them till they touched the rest. When i can afford to, I will be getting 2dz. FMJ's of the 300 spine, cut them much longer, wrap them, put Aerovanes on them, and get Silver Flames.

    Barry; There is only one version, to be improved in januart with the Gen. II.

  9. #9
    Banned
    Join Date
    Dec 2008
    Location
    Henry, IL
    Posts
    22
    Post Thanks / Like

    Default Aerovane II spec are...

    I am still tweaking Aerovane II, if surface treatment and dimples pan out, You may be looking at a vane that is about 4.7 grains each with another 6% increase in spin! In am still doing more testing. Base on the current sample without the surface treatment, it flew the same as aerovane I with 30 grain penalty. i.e. after I added 30 grains to the arrow with aerovane II, it few the same as aerovane without any surface treatment applied yet! With surface treatment, alone, aerovane shows a 4 inches improvement over non treatment at 55 yards. And it also do another 5 inches (total 9 inches) improvement after we added the concave to reduce air to surface drag on the high pressure side (back side). If all is done right, Aerovane II should hit no less than 12 - 19 inches higher than Aerovane at 55 yards.

    I am using the FC 1.3 on my arrow right now with FirstCut XT head (I like it even better than Silver Flame due to price and the bleeder. Can you believe it used to be about $15 for 3, and its blade is 0.058".

    This is what Aerovane II should looks like.

    What you see is FC1.3 (final candidate 1.0 revision 3), no surface treating has been done on it yet and all final smoothing and angular process have not been applied! And it is going to be about 5.9 grains each.




    The picture is my setup which I took when I am on the stand at 4:04pm a few days ago.


  10. #10
    Super Moderator bfisher's Avatar
    Join Date
    Nov 2005
    Location
    Middletown, Pa, USA
    Posts
    11,584
    Post Thanks / Like

    Default

    So what surface treating is it going to be and for what purpose? Also what's the height of the vane? I may or may not use a drop away rest. All depends.
    If You're Not Living on the Edge You're Taking Up Too Much Space
    Martin Gold Plus Staff Shooter
    Alien Mafia
    PSAA Life member, UBP Life member
    PADI AOW Diver

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •