Results 1 to 10 of 17

Thread: Idler worn off after 21/2 months on new Jaguar ?

Hybrid View

  1. #1
    romi
    Guest

    Question Idler worn off after 21/2 months on new Jaguar ?

    Hi,
    I would like to know if it is normal to have idler wheel worn off on one side ( towards cable guard ) to rasor sharp edge ? I noticed that braiding on this side of the bow started to fall appart and after fiding out what's wrong, I am not surprised. Is this normal on factory setup bow bought completelly new 21/2 monhs ago at Pro Shop?

    Thank you,
    Roman

  2. #2
    Myk
    Guest

    Default

    No that is not normal and it doesn't sound safe to shoot.
    I shot my Phantom II Fuzion a lot for 2 years and never had anything like that.

    You should take it to your pro shop for repair. If the pro shop is no longer there contact Martin.

    I can think of why it's doing it, because the angles of the strings to the cable guard is extreme on short bows and you may be shooting a high profile fletching requiring that angle to be even more extreme. You also must have some kind of dirt or abrasive dust getting on it.

    After it's fixed I would think about waxing the serving, if you're using Blazers switch to a normal profile vane, cut your cable clearance down to a minimum and keep the bow stored in a case.

  3. #3
    romi
    Guest

    Question

    This bow is new, with original string on it , the serving on the side of idler is falling appart even though the string itself seems to be OK for now. But I agree with you, I don't think it is safe. The guard is set as it came from Martin as the guy in the pro shop didn't tamper with it as it would require to remove the sight first due to the locking screws position. And I can see how far from the centre line it is pulling the cables! I am completelly new to this so I didn't notice it until now and thought that the string wear is normal with my shooting about 250-300 arrows a week. For starting, I am using RedHead Carbon Fury arrows with plastic vanes which don't seem to be that big. The clearance seems to be rather big, about 3/8 between the vane and the cables.
    My bow is Jaguar Magnum 31" 60# set at 55#
    and I do have big honky plastic carrying case where the bow is when I am not playing with it.

  4. #4
    Myk
    Guest

    Default

    Your cable guard clamp screw is on the wrong side if you have to remove your sight to get at it. When it's apart have the clamp swapped around. It should be accessible from the other side.

    I don't think cable guards come installed from the factory. Either the user or the prop-shop puts them on and sets them.
    I'm not sure if the bow packages come all assembled or not.

    3/8" clearance is way too much. I have 1/16" on my Phantom II Mag Dyna and none of my arrows show signs of hitting.
    It's still odd it would wear that fast especially since it's stored in a case. I have all kinds of abrasive dusts in my house and never had anything like that.

  5. #5
    romi
    Guest

    Default

    It is odd, isn't it. Considering its supposed to be anodized aluminium. It is really paper thin. I would expect this from some cheap aluminium. But not this fast anyway. No excessive amount of dust in the house, maybe little dog hair. That would have to be really abrasive stuff anyway to cause this that fast. Unless the serving is made of something like that...

    Thank you for the info

  6. #6
    Stash
    Guest

    Default

    romi bought the bow from the store where I work. He brought it in today, and I was amazed - I have never seen anything like it. The idler wheel is machined completely off-center - the right side of the groove is as he described, knife-sharp and the left side is abnormally thick. It's not worn - it was just machined badly.

    We have replaced his Jaguar with a new one and will be contacting Martin regarding replacing the idler and string.

    I will try to take some photos of the idler on Monday and post them here. Looks like this:
    Attached Images Attached Images

  7. #7
    Stash
    Guest

    Default

    Quote Originally Posted by Myk
    Your cable guard clamp screw is on the wrong side if you have to remove your sight to get at it. When it's apart have the clamp swapped around. It should be accessible from the other side.

    I don't think cable guards come installed from the factory. Either the user or the prop-shop puts them on and sets them.
    I'm not sure if the bow packages come all assembled or not.
    This Jaguar package does come pre-assembled from the factory with a plastic 3-pin sight/bowquiver mount, and the cable guard is tightened with 2 small set screws that are under the sight mount. romi has changed the sight that originally came with his bow, but the cable guard was still in its original factory-set position. I don't think that the amount of offset was in any way responsible for the problem. Just a bad idler wheel.

  8. #8
    Myk
    Guest

    Default

    I just looked at the '06 Jags, so they don't have the same clamp system as the others? They also still have the slotted berger (which I liked).

    I agree, if the center of the bottom of the groove is off center like your picture it was machined that way. Very strange that a CNC machine would be that far off in that direction.
    Must've been start of Monday shift or end of Friday shift work

  9. #9
    Stash
    Guest

    Default

    Pic of the idler...
    Attached Images Attached Images

  10. #10
    hunter
    Guest

    Default

    I would say..No, That is not normal.. and I bet martian takes care of it for you ..There service has always been good to me ..

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •