Results 1 to 10 of 22

Thread: Wild Turkey Feather Spiral Flu Flu's

Hybrid View

  1. #1
    Senior Member ElkSlayer's Avatar
    Join Date
    Feb 2010
    Location
    Oregon
    Posts
    1,050
    Post Thanks / Like

    Default Wild Turkey Feather Spiral Flu Flu's

    Step one, harvest said bird ! Once you get that done the rest is easy...
    I removed the whole wing, took each feather off later in the year.

    I split the quill with an exacto knife, in the natural crease.

    Then stand it on edge, looking down at feather edge you will see the curve of growth.
    Trim any extra quill away on both sides to blend quill base to match the mid portion. Keep knife parallel to feather creating a square bottom..
    ( be sure to trim close enough to thin quill so it will bend. I tested it by trying to make a circle with out causing any kinks in the quill ) be sure to leave a tag end on base on quill.
    I used my fletching jig's stright clamp to hold feather while I sanded the bottom of quills spongey core to a thin flat layer...
    keep it on the same plane .. ( I used 320 wet/ dry) be carful paper will try to grab feather so sand slow and easy..not trying to remove metal here re test with circle technique.. once your happy with it move on to step 4

    I tried to apply a straight feather to an arrow and it worked out ok, but was not the best way.. Latter found if I pre wraped quill around shaft and split feather barbs to make up small sections it was easer.. either way works

    First deside where you want to start at nock end. then tape tag end in place to start your wrap again ( if you did the pre wrap method)
    I had the wife run the glue bead while i held tight on feather an slowly turned arrow shaft.

    Once wraped up, tape the end down. set aside to dry I let 'em set a few hours then I removed tape , trimed tag ends off, added a drop of glue on each..let that dry and went shooting I'm getting 40 yds max on a leval shot out of my Fury 48lbs@ 28" but I pull 31
    Last edited by ElkSlayer; 11-30-2010 at 03:43 PM.
    It's all fun an games till you put that big boy on the ground.. now its time to get to work
    Martin cougarIII elite nitrous C cam X system & HHA
    Darton Fury recurve

    http://www.cascadianbowmen.org/

  2. #2
    Senior Member alex's Avatar
    Join Date
    Nov 2008
    Location
    Bulgaria
    Posts
    1,366
    Post Thanks / Like

    Default

    Looks very good.
    2008 Martin MOAB - 45-60#, set at about 51-53# / 55#" Perfect Line" compound/ 55# Mongol horsebow/ 45# "Perfect Line" takedown recurve/ 45# Bearpaw Grizzly hunter recurve/ 55# Samick Longbow Cheetah ... and several homemade bows

  3. #3
    Senior Member ElkSlayer's Avatar
    Join Date
    Feb 2010
    Location
    Oregon
    Posts
    1,050
    Post Thanks / Like

    Default

    thanks alex..it was a lot of fun doing it too.. some thing i rememberd from my youth..now to get a mess of um together and have some fun... folks had a milk jug lancher..thats next on list to be built...need more arrows
    It's all fun an games till you put that big boy on the ground.. now its time to get to work
    Martin cougarIII elite nitrous C cam X system & HHA
    Darton Fury recurve

    http://www.cascadianbowmen.org/

  4. #4
    Senior Member elkslayer4x5's Avatar
    Join Date
    Mar 2008
    Location
    Lane County, Oregon
    Posts
    2,857
    Post Thanks / Like

    Default Launcher

    We used half galleon milk cartons back then. I'll be using 2 liter plastic bottles now with sand or water in them, just enought to help them fly better. Power it with surgical tubing, trigger it with any old release.
    http://eastoutfitter.tripod.com/index.html
    http://www.cascadianbowmen.org/
    Martin 06 Slayer, Nitrous C, shoot thru, 63lb, Quiktune 3000, HAA OL 5519, Beman ICS Hunter
    Martin 06 Slayer, Nitrous C, Shoot thru, 55lb, Quiktune 3000, HHA OL 5519 2X, Easton A/C/C
    Ben Pearson 1968 'Cougar' 62" 45#s @ 28" recurve, parallel shaft POC, Zwickey 'Eskimo' 2 blade

  5. #5
    Senior Member ElkSlayer's Avatar
    Join Date
    Feb 2010
    Location
    Oregon
    Posts
    1,050
    Post Thanks / Like

    Default

    just like shooting clays with a shotgun.. its a hoot
    It's all fun an games till you put that big boy on the ground.. now its time to get to work
    Martin cougarIII elite nitrous C cam X system & HHA
    Darton Fury recurve

    http://www.cascadianbowmen.org/

  6. #6
    Senior Member ElkSlayer's Avatar
    Join Date
    Feb 2010
    Location
    Oregon
    Posts
    1,050
    Post Thanks / Like

    Default a few more

    here is one i did up for the boy RW tight wrap (left pic/ blue x7)...best looking one todate ..when its time to redo mine it will be this way. I do not expect them to last forever they already are showing use..wraped mine base @ nock his was tip @ nock with a tight wrap.. did another LW tip @ nock long wrap it works out to 30 alslo...
    Attached Images Attached Images
    It's all fun an games till you put that big boy on the ground.. now its time to get to work
    Martin cougarIII elite nitrous C cam X system & HHA
    Darton Fury recurve

    http://www.cascadianbowmen.org/

  7. #7
    Senior Member ElkSlayer's Avatar
    Join Date
    Feb 2010
    Location
    Oregon
    Posts
    1,050
    Post Thanks / Like

    Default

    Why yes it is....waiting to get my privite property permission card..should have it end of the week...as you know Im slingin arrows to get ready so is rhino... tic tic tic DRT TOM'S....LOL
    It's all fun an games till you put that big boy on the ground.. now its time to get to work
    Martin cougarIII elite nitrous C cam X system & HHA
    Darton Fury recurve

    http://www.cascadianbowmen.org/

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •